Lenze MCH Series Drives Metasys N2 Instrukcja Użytkownika Strona 1

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Sprzęt komputerowy Lenze MCH Series Drives Metasys N2. Lenze MCH Series Drives Metasys N2 User Manual [it] Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
  • Strona
    / 15
  • Spis treści
  • BOOKMARKI
  • Oceniono. / 5. Na podstawie oceny klientów
Przeglądanie stron 0
MCH Series Drives
Metasys N2 Communications Guide
Przeglądanie stron 0
1 2 3 4 5 6 ... 14 15

Podsumowanie treści

Strona 1 - MCH Series Drives

MCH Series Drives Metasys N2 Communications Guide

Strona 2 - About These Instructions

7 RG-MHMETN2 Points4.2 Analog Input (AI) Point DescriptionsPoint Description1-01: Actual Frequency This point represents the actual speed of th

Strona 3 - Contents

RG-MHMET 8N2 PointsPoint Description1-08: PID Setpoint Command This point is for monitoring the commanded PID Setpoint and is displayed in the dri

Strona 4 - Safety Information

9 RG-MHMETN2 Points4.3 Binary Input (BI) Point DescriptionsPoint Description2-01: PID Mode This point is for monitoring the general state of th

Strona 5

RG-MHMET 10N2 Points4.4 Analog Output (AO) Point DescriptionsPoint Description3-01: Acceleration Rate This point sets the time that it will take

Strona 6 - Introduction

11 RG-MHMETN2 PointsPoint Description3-05: Keypad Setpoint Command This point monitors and controls the Keypad Setpoint Command. The units for t

Strona 7 - Drive Setup & Programming

Lenze AC Tech Corporation630 Douglas Street • Uxbridge MA 01569 • USASales: 800-217-9100 •Service: 508-278-9100www.lenze-actech.comRG-MHMET-e6

Strona 8

This documentation applies to the use of an MCH Series Variable Frequency Drive with Metasys N2 protocol and should be used in conjunction with

Strona 9

i RG-MHMETContents1 Safety Information ...

Strona 10 - N2 Points

1 RG-MHMETSafety Information1 Safety Information1.1 Warnings, Cautions and Notes1.1.1 GeneralSome parts of Lenze controllers (frequency inverter

Strona 11

RG-MHMET 2Safety Information1.1.4 Electrical ConnectionWhen working on live drive controllers, applicable national regulations for the prevention of

Strona 12

3 RG-MHMETIntroduction2 IntroductionThis document will explain how to operate a Lenze-AC Tech MCH Variable Frequency Drive using Metasys N2 proto

Strona 13

RG-MHMET 4Drive Setup & Programming3 Drive Setup and ProgrammingMost drive parameters (including those required for serial communications) are n

Strona 14

5 RG-MHMETDrive Setup & Programming60 SERIAL TIMEOUT This parameter makes the serial watchdog timeout period selectable. It has a m

Strona 15 - Lenze AC Tech Corporation

RG-MHMET 6N2 Points4 MCH N2 PointsThe MCH N2 Points are divided into four types: analog input, binary input, analog output and binary output. Sectio

Komentarze do niniejszej Instrukcji

Brak uwag