Lenze DSD Instrukcja Użytkownika Strona 436
- Strona / 496
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
17 Restrictions of the drive dimensioning
17.17 Parallel operation of several motors on one inverter (group drives)
436
Lenze · Drive Solution Designer · Manual · DMS 4.2 EN · 12/2013 · TD23
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
17.17 Parallel operation of several motors on one inverter (group drives)
Such a dimensioning at present is not yet supported by the DSD.
[17-6] Group drives
Remedy
When entering the data in the DSD, divide the masses, moments of inertia, and tensile forces or
counterforces by the number of motors involved in the application (applies to the motor and gear-
box selection). The inverter in this case has to be selected manually, since it has to operate the sum
of the motors.
Note!
Relevant only for specific applications, e. g. hoists, winders, caterpullar take-offs, pumps
and power conveyors.
M
3 (2)
P
mot
P
gen
P
mot
P
gen
i
1
i
1,1
M
P
mot
P
gen
i
2
i
2,1
M
P
mot
P
gen
i
n
i
n,1
9352
R
B
3 ~
3 ~
- Drive Solution 1
- Designer 1
- Contents 10
- 1 Notes on usage 11
- 2 About this documentation 14
- Pictograph and signal word! 17
- 3User interface 18
- How to sort the results: 35
- How to filter results: 35
- How to open created notes: 38
- How to delete notes: 38
- 4.3.1 Messages 44
- 4.3.2 Software updates 45
- 4.4 Language 46
- 4.5 Settings 46
- 4.5.3 "Help" tab 47
- 4.5.5 "Units" tab 48
- User data 50
- Registration data: 50
- 4.6 User-specific settings 51
- 4.6.1 User-defined defaults 51
- 5Managing projects 52
- 6 Drive dimensioning tools 55
- 7Applications 100
- Mass calculator ( 405) 109
- Danger! 122
- Pole pair 191
- 8 Motion design 224
- symbol in the toolbar 225
- CINH = 1 271
- 9 Mains and environment 277
- ( 283) 282
- ( 285) 282
- ( 286) 282
- 10.1 Mechanical drive axis 283
- 10.1.1 Lenze gearbox 283
- 10.1.3 Feedback 284
- 10.2 Electrical drive axis 285
- 10.3 Drive concept 286
- 10.3.1 Gearbox features 287
- 10.3.1.1 Axial gearbox 287
- 10.3.1.2 Right-angle gearbox 288
- 10.3.2 Motor properties 289
- 10.3.4 Inverter properties 294
- 10.3.4.1 Frequency inverter 294
- 10.3.4.2 Servo inverters 296
- 11 Drive Dimensioning 308
- 12 Components in the DC bus 361
- 13 Details on Lenze products 377
- 14 Energy efficiency 378
- 15.1 Drawing 386
- Editing functions 389
- 15.2 Results 390
- 15.3 Protocols 391
- 15.3.1 Summarised protocol 391
- 15.3.2 Detailed protocol 391
- 15.3.3 Commissioning data 392
- 15.3.5 Output settings 393
- 15.4.1 Application Tuner 394
- 15.4.3 BlueGreen 394
- ( 378) 395
- 15.6.1 Dynamic reserves 396
- 15.6.2 Stationary reserves 396
- 15.6.3 Speed reserves 397
- 15.6.7 Reserves for gearboxes 399
- 16 Auxiliary means 401
- How to call the calculator: 404
- How to call the DSC: 425
- 17.1 Field weakening 426
- 17.5 Feedback systems 427
- Measured values 430
- 17.16 System disturbances 435
- [17-6] Group drives 436
- 17.19 ATEX for gearbox 437
- 17.21 Emergency-off scenarios 438
- 18.1 Applications 441
- 18.2 Drive system 445
- 18.3 Additional drive element 449
- 18.4 Lenze gearbox 450
- 18.5 Lenze motor 455
- 18.5.6 Motor speed too low 456
- > as winding ratio q 460
- 18.6 Brake 461
- 18.6.3 No brake available 461
- 18.7 Feedback 463
- 18.7.2 No feedback selected 463
- 18.8 Inverters 465
- 18.8.16 Activate VVC control 469
- 18.8.19 Mains choke required 470
- 18.10 Supply module 476
- 18.11 Brake chopper 479
- 18.12 Brake resistor 481
- 18.13 User motor 483
- ( 42) 485
- ( 46) 485
- 20 Glossary 486
- )(('%$& 494
Powiązane produkty i podręczniki dla Oprogramowanie Lenze DSD
Oprogramowanie Lenze PLC Designer Migration PLC Designer (R2-x)-PLC Des Instrukcja Użytkownika
(30 strony)
(30 strony)
Oprogramowanie Lenze PLC Designer ApplicationTemplate (PLC Designer R3- Instrukcja Użytkownika
(177 strony)
(177 strony)
Oprogramowanie Lenze PLC Designer PLC Designer (R2-x) CANopen for Runti Instrukcja Użytkownika
(56 strony)
(56 strony)
Oprogramowanie Lenze PLC Designer PLC-Designer (R2-x) SoftMotion Instrukcja Użytkownika
(290 strony)
(290 strony)
Oprogramowanie Lenze ApplicationTemplate PackML (PLC Designer R3-x) Instrukcja Użytkownika
(99 strony)
(99 strony)
(270 strony)
Oprogramowanie Lenze i700 Instrukcja Użytkownika
(338 strony)
(338 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji